subscribe
 

Venting solutions protect electronics against environmental impacts

26th November 2014


The graph shows the continuous buildup of negative pressure within a hermetically sealed housing. In unvented housings, as little as 7kPa of pressure can be enough to cause seals to fail after several temperature cycles. Vented housings equalise pressure and avoid seal leakage The graph shows the continuous buildup of negative pressure within a hermetically sealed housing. In unvented housings, as little as 7kPa of pressure can be enough to cause seals to fail after several temperature cycles. Vented housings equalise pressure and avoid seal leakage
Venting components requires greater airflow per membrane surface area, resulting in a lower water entry pressure Venting components requires greater airflow per membrane surface area, resulting in a lower water entry pressure
The results: Values below the black horizontal line indicate that applying the chemicals has impaired the membrane. The test membrane has only limited suitability for wetting with corrosion protection (removal) agents, but lies within the prescribed standards for all other chemicals tested The results: Values below the black horizontal line indicate that applying the chemicals has impaired the membrane. The test membrane has only limited suitability for wetting with corrosion protection (removal) agents, but lies within the prescribed standards for all other chemicals tested

Robert Chamberlain looks at how to ensuring the long-term functionality of electronic parts in vehicles.

In vehicles, mechanical parts are increasingly replaced by electronic components. Driver assistance systems like adaptive cruise control or lane-assist become more and more common, and the number of electronic components built into vehicles is constantly rising. That is why today, more than ever, car manufacturers and their suppliers have to look for effective ways to protect in-vehicle electronics against environmental impacts and failures. A proper protection is key to ensure premium quality and reliability of today’s automobiles. And these aspects, in turn, are relevant for building and retaining a customer confidence and brand loyalty.

All electronic components – whether part of compressors, pumps, motors, control units or sensors for increasingly popular active security systems – are subjected to huge temperature fluctuations throughout their service life. These can arise when the component’s housing heats up in operation and then comes into contact with cold spray from the road or at the carwash. These fluctuations in temperature can cause a significant vacuum to develop inside the electronics housing. The resulting pressure differential can be so strong that the seals and sealing components protecting the sensitive electronics can be seriously compromised, letting in dirt particles and liquids that can corrode the component and shorten its service life. Damaged or defective components usually have to be replaced, leading to high warranty and repair costs for automakers and their suppliers.

Challenges

One major challenge facing the automotive industry is the thermal management of high-performance electronics and batteries in electric vehicles, since these components need to operate in a certain temperature range in order to achieve optimum performance. They get very hot when running and need to be cooled using fluids. This can cause such huge temperature differentials within the electronic unit itself that condensate can form at the coldest point in the housing, which can lead to corrosion or cause a short circuit.

For large battery housings, this problem can be so extensive that it is difficult to solve without effective measures to equalise temperature and pressure. Given the housing’s size, even minor temperature differentials can put enough pressure on the housing to cause deformation.

In certain circumstances, driving a car out of a warm garage into the cold winter air can produce an interior vacuum that exerts a negative pressure of 500 kilograms per square metre. Lightweight housings are scarcely able to withstand such pressure.

Membrane technology

OEMs generally deal with these problems in one of three ways. The first option is to pot the electronic components. While this solution creates a perfectly sealed system, the unit ends up significantly heavier and cannot be reopened and repaired if it fails.

Another way to achieve a hermetically sealed system is to use high-quality seals and thicker housing walls. The drawback of this system, however, is that it makes components more expensive and unnecessarily heavy.

A common and much more sensible solution is to incorporate a membrane that equalises the air inside the housing while at the same time preventing the ingress of liquids and dirt particles.

Airflow and water entry pressure

Airflow and water entry pressure are the two fundamental characteristics that determine a membrane’s performance. Airflow describes how much air can pass through the membrane in a given period, at a given differential pressure. This defines how long it would take to equalize a pressure differential. Water entry pressure is the minimum hydrostatic pressure that the membrane must be able to withstand before it leaks. Both parameters are influenced by the pore size of the membrane, among other factors. It is the membrane supplier’s job to provide the ideal combination of airflow and water entry pressure for each individual application.

A major challenge in the automotive industry is the trend toward increasingly compact electronic components. This means venting components must also become smaller if they are to be integrated into smaller housings as effectively as possible. This in turn requires greater airflow per membrane surface area, resulting in a lower water entry pressure.

Typically, a system’s imperviousness is determined by ascertaining its IP protection rating (according to DIN 40050-9). The IP test determines the electronics housing’s protection level against solid objects and liquids. The IP protection rating is defined by two digits: IPXY. The first digit (X) indicates the protection rating against ingress of solid foreign objects; the second digit (Y) indicates the level of protection against ingress of liquids. IPX9K shows how well the housing with integrated membrane is able to remain watertight when exposed to steam jets.

The IPX9K test is carried out in a testing chamber in which the housing, including its integrated membrane, is exposed to a steam jet from a distance of 100 to 150mm, at angles of 0, 30, 60 and 90 degrees. The airflow rate is kept between 14 and 16l/min, water pressure maintained at between 8,000 to 10,000kPa and temperature at 80°C.

ePTFE membranes

A material that is ideally suited to venting applications because of its unique microstructure is PTFE (polytetrafluoroethylene). The PTFE raw material is stretched in a specially designed process to create a membrane with very fine pores and in which the nodes are interconnected by fibrils. This material, called expanded polytetrafluoroethylene or ePTFE, is extremely hydrophobic (water resistant) thanks to its low surface tension, which means that any water droplets on the surface are unable to penetrate the membrane structure. The membrane is also oleophobic (oil resistant) and repels liquids with low surface tensions, such as oils. ePTFE’s oil-repelling properties are particularly important for applications in the automotive industry, as the likelihood is very high that vehicle components will come into contact with motor oil, cleaning agents or other automotive fluids.

In order to test how well venting solutions are able to withstand up to 20 different chemicals (in accordance with the ISO 16750-5 standard) the vents are exposed to each test liquid and then left for 24 hours at room temperature (21 to 23 °C) or heated for 96 hours in an oven. Airflow and water entry pressure are measured before and after the test. Both results must lie within prescribed specifications.

High temperatures

Another advantage of PTFE is its extremely high resistance to extreme temperatures. Its ability to withstand temperatures ranging from -150°C to 240°C is a property that is important given the current trend toward reducing engine size while maintaining or even improving performance. Shrinking the size of engines in this way usually pushes temperatures above the 125°C threshold that electronic housings have been designed to cope with until now. It is no longer uncommon for temperatures to reach 150°C and above.

There are several proven methods of testing vents to determine their ability to withstand extreme temperatures (ISO 16750-4).

In the temperature resistance test, the vent is exposed to a maximum temperature of up to 150°C for 2,000 hours, or a minimum of -40°C for 1,000 hours. In the ice dunk test, the vent is placed in a sealed housing and heated at a temperature between 80 and 120°C in an oven for 40 to 60 minutes. The housing is then rapidly cooled to between 0 and 4°C by placing it in iced water containing 5% sodium chloride, a solution designed to simulate the salt water that electronic housings are likely to come into contact with in the winter. This procedure is repeated ten to twenty times, with venting properties measured before and after the test.

Choosing the right membrane to suit each particular application and its requirements is vitally important. In order to cover all application areas, membrane manufacturer offer adhesive and weldable vents as well as moulded parts. Adhesive Vents are coated with a high-performance adhesive that adheres strongly to various kinds of metal and plastic. They are supplied on a lightly adhesive backing for manual or automated installation. The adhesive is long-lasting and capable of withstanding harsh conditions. However, as the adhesive has only limited resistance to extremely high temperatures and strong chemicals, these vents are less suitable for under-the-hood use. They are designed to be used with vehicle components that are less likely to come into contact with liquid chemicals, such as automotive lamps.

Weldable vents can be made of different material combinations and in different sizes to suit the specific requirements of the intended application. They are mainly used in applications with plastic housings, and are attached by the customer using ultrasonic welding. At the weld seam a small section of the housing material melts and flows into the porous structure of the membrane, thereby guaranteeing that the join is sealed and solid. Since the melting point of PTFE is much higher than the welding temperature, this process does not compromise the membrane. These vents provide a long-lasting, reliable solution even when exposed to high temperatures and strong chemicals. However, the welding process is very complex and requires specialised welding tools and qualified experts to complete the process. In addition, protective walls have to be integrated into the housing design to protect the vent from steam jets and mechanical loads, which can be an expensive and complicated process.

Moulded parts represent a solution that is able to withstand the most challenging environmental conditions as well as being easy to integrate. This can be achieved by adding a step to the manufacturing process. For example, insert moulding is a process that integrates the membrane directly as part of the plastic injection moulding process. The moulded parts can then be attached by simply snapping them into place in an opening in the housing. This protects the membrane from mechanical loads without the need to integrate expensive and complex protective walls into the housing. Furthermore, integrating the vent does not call for special machines or qualified experts: the vent is simply fitted in the housing via the ‘plug & play’ method.

Tailored venting solution

Pressure equalisation of electronics and batteries in vehicles is a major challenge for carmakers in order to guarantee best performance and long-term reliability. An effective solution is to incorporate a membrane that equalises the air inside the housing and protects it against liquids and dirt.

In order to determine the best venting solution, it is important to involve a supplier at the earliest stage in the design process. This ensures that each venting solution undergoes the necessary testing for its intended application and meets the correct requirements. As soon as all customer specifications are clarified, the proper solution can be selected. 

Robert Chamberlain, Sales Manager Automotive Electronics, W L Gore & Associates, Ltd, Nottingham, UK. 







Subscribe

Subscribe



Newsbrief

twitter facebook linkedin © Setform Limited